Log In
New user? Click here to register. Have you forgotten your password?
NC State University Libraries Logo
    Communities & Collections
    Browse NC State Repository
Log In
New user? Click here to register. Have you forgotten your password?
  1. Home
  2. Browse by Author

Browsing by Author "Andrey Kuznetsov, Committee Member"

Filter results by typing the first few letters
Now showing 1 - 2 of 2
  • Results Per Page
  • Sort Options
  • No Thumbnail Available
    The Impact of Input Energy, Fiber Properties, and Forming Wires on the Performance of Hydroentangled Fabrics
    (2003-10-29) Zheng, Huabing; Mohamed Bourham, Committee Member; Andrey Kuznetsov, Committee Member; Behnam Pourdeyhimi, Committee Member; Donald Shiffler, Committee Co-Chair; Abdelfattah Seyam, Committee Chair
    Extensive critical literature review of the development of hydroentangled technology and research regarding fabric performance in terms of fiber and process parameters was conducted. The review revealed that hydroentanglement is the fastest growing nonwoven bonding technology with an annual growth rate of about 20%. The review also indicated that the research in public domain regarding fabric performance as related to forming wire geometry and fiber properties is not thoroughly covered. The research areas in process and fabric geometry modeling have not been considered by previous researchers. A model describing the force and energy required to form fabric aperture was derived by developing hydroentangled fabric geometry and calculating the energies required to achieve the geometry. Three energy components were considered, namely fiber bending, fiber-to-fiber friction, and fiber stress-strain. The model predicts the three energies in terms of fiber properties and forming wire geometry. Numerical examples illustrating the use of model to calculate the three energies for range of forming wires a fiber are given. The numerical solution shows that the calculated energies from the model that is required to form fabrics is extremely very small as compared to the water jet energy. This indicates that most of the energy is lost. Experimental trials were conducted using different fibers with range of properties, forming wires, and water jet pressure. Fabric tensile strength is used as an indicator of degree of hydroentanglement to assess the fabric performance. The results show that the hydroentangled fabric tensile strength is significantly influenced by forming wire type, fiber properties, and jet pressure. Three force mechanisms (flexural rigidity, friction force, and strain force) were analyzed to reveal which force is more significance in governing fabric strength.
  • No Thumbnail Available
    Residence Time Distribution of Multiple Particles in Four Configurations of Holding Tubes
    (2004-11-15) Tanyel, Zeynep; Andrey Kuznetsov, Committee Member; Saad Khan, Committee Member; K.P. Sandeep, Committee Chair; Josip Simunovic, Committee Member
    Residence time distributions of multiple particles (as affected by process and system parameters) were investigated during non-Newtonian tube flow. Process parameters included flow rate, particle type, carrier fluid viscosity, and particle concentration. The system parameter of interest was the holding tube configuration. Polystyrene and acrylic particles were used as model food particles. Digital imaging analysis was used to obtain residence time data of particles. A novel type of holding tube (chaotic holding tube) was constructed. Comparisons among the straight, single helical, double helical, and chaotic holding tube were performed in terms residence time distribution (RTD) of particles. In addition, the effect of inclination angle (0 ° and 45 °) of the chaotic holding tube was investigated. It was found that the narrowest RTD of particles was obtained in the single helical holding tube. RTstd in the chaotic holding tube was greater than that in the single helical holding tube, but lower than those in the straight and double helical holding tubes. The most significant process parameter affecting RTD was flow rate. The effect of flow rate was more pronounced for high density (acrylic) particles. Carrier fluid viscosity, particle type, and particle concentration did not have significant effects on the overall RTstd. Trends observed in the chaotic holding tube were similar to those observed in the single helical holding tube. However, there were some cases where use of chaotic holding tube resulted in narrower RTD of particles. Changing the inclination angle from 0 ° to 45 ° in the chaotic holding tube resulted in wider RTD of both types of particles.

Contact

D. H. Hill Jr. Library

2 Broughton Drive
Campus Box 7111
Raleigh, NC 27695-7111
(919) 515-3364

James B. Hunt Jr. Library

1070 Partners Way
Campus Box 7132
Raleigh, NC 27606-7132
(919) 515-7110

Libraries Administration

(919) 515-7188

NC State University Libraries

  • D. H. Hill Jr. Library
  • James B. Hunt Jr. Library
  • Design Library
  • Natural Resources Library
  • Veterinary Medicine Library
  • Accessibility at the Libraries
  • Accessibility at NC State University
  • Copyright
  • Jobs
  • Privacy Statement
  • Staff Confluence Login
  • Staff Drupal Login

Follow the Libraries

  • Facebook
  • Instagram
  • Twitter
  • Snapchat
  • LinkedIn
  • Vimeo
  • YouTube
  • YouTube Archive
  • Flickr
  • Libraries' news

ncsu libraries snapchat bitmoji

×