Piezoelectric, Dielectric and Ferroelectric Thin Films on Metal Substrates for Microelectronic Applications

Show simple item record

dc.contributor.advisor Angus Kingon, Committee Chair en_US
dc.contributor.author Srinivasan, Sudarsan en_US
dc.date.accessioned 2010-04-02T18:33:41Z
dc.date.available 2010-04-02T18:33:41Z
dc.date.issued 2006-10-06 en_US
dc.identifier.other etd-07082005-135715 en_US
dc.identifier.uri http://www.lib.ncsu.edu/resolver/1840.16/3633
dc.description.abstract The purpose of this research has been to demonstrate the possibility of integrating piezoelectric, dielectric and ferroelectric- lead and barium based oxide thin films and PVDF polymer on flexible metal substrates for microelectronic applications. Investigations on the key processing parameters and properties relationship for lead zirconate titanate (PZT, 52⁄48) and barium zirconate titanate (BZT, 35⁄65) based thin films on Cu foils were performed and studied. The impact of the oxygen partial pressure on the electrical properties of PZT and BZT thin films during processing has been explored, and demonstrated that high quality films and interfaces can be achieved through control of the pO2 within a window predicted by thermodynamic stability considerations. It should be noted that the high temperature processing of barium based ferroelectric oxides can be processed on Cu foils in a wider window of pO2 compared to that of processing lead based ferroelectric oxides. Also, the high volatile nature of lead makes the processing of lead based ferroelectric oxides difficult. Considering these issues, this work shows the processing technique undertaken to achieve high quality barium and lead based oxide thin films on Cu foils. The demonstration has broad implications, opening up the possibility of the use of low cost, high conductivity copper electrodes for a range of Pb-based and Ba-based perovskite materials, including PZT films in embedded printed circuit board applications for capacitors, varactors, and sensors; multilayer PZT piezoelectric stacks; and multilayer lead magnesium niobate-lead titanate-based dielectric and electrostrictive devices. In the case of ferroelectric PZT films on Cu foil, the capacitors do not fatigue upon repeated switching like those with Pt noble metal electrodes. Instead they appear to be fatigue-resistant like ferroelectric capacitors with oxide electrodes. This may have implications for ferroelectric nonvolatile memories. The effect of electrodes on the electrical properties of lead zirconate titanate has been investigated and discussed. For systematic and comprehensive analysis of the electromechanical properties, an accurate analytical modeling has been developed. The analytical modeling derived can be applied to double end clamped (under various end conditions) beam geometry that is useful for the case of compliant actuator material (eg. PVDF polymers) and applications, that involve high resonance of operation. These analytical expressions represent the first set of derivations for flexural mode actuators under dynamic conditions, which yield both the resonant frequencies and the displacement at resonance of double end clamped piezoelectric actuators. These analytical expressions allow users to optimize the materials selection and dimensions of bimorph and unimorph actuators. The reliability of the analytical expressions derived has been investigated using experimental results performed on PVDF polymer as a piezoelectric actuator. The actuators were constructed as double end clamped beams (both bimorph and unimorph cases). They were operated in flexural mode. The two ends of the actuator were clamped such that the slope at both the ends of the actuator bending curvature at resonance is zero. This type of end condition results in increasing the resonance frequency. en_US
dc.rights I hereby certify that, if appropriate, I have obtained and attached hereto a written permission statement from the owner(s) of each third party copyrighted matter to be included in my thesis, dissertation, or project report, allowing distribution as specified below. I certify that the version I submitted is the same as that approved by my advisory committee. I hereby grant to NC State University or its agents the non-exclusive license to archive and make accessible, under the conditions specified below, my thesis, dissertation, or project report in whole or in part in all forms of media, now or hereafter known. I retain all other ownership rights to the copyright of the thesis, dissertation or project report. I also retain the right to use in future works (such as articles or books) all or part of this thesis, dissertation, or project report. en_US
dc.subject microelectronics en_US
dc.subject oxygen en_US
dc.subject fatigue en_US
dc.subject PZT en_US
dc.subject copper en_US
dc.subject BZT en_US
dc.subject piezoelectric en_US
dc.subject actuators en_US
dc.subject dielectric en_US
dc.subject Ferroelectric en_US
dc.title Piezoelectric, Dielectric and Ferroelectric Thin Films on Metal Substrates for Microelectronic Applications en_US
dc.degree.name PhD en_US
dc.degree.level dissertation en_US
dc.degree.discipline Materials Science and Engineering en_US


Files in this item

Files Size Format View
etd.pdf 10.91Mb PDF View/Open

This item appears in the following Collection(s)

Show simple item record